When designing a belt conveyor, the first questions are: Which belt width and belt speed will carry the required capacity? How steep can the conveyor be? How many kW of motor are needed? In this guide we explain the basic steps of belt conveyor calculation, practical formulas for capacity and motor power, and a worked example.
Note: The method here is for preliminary sizing. The final design of long, high-capacity, steep or critical conveyors should be carried out to design standards such as DIN 22101 or ISO 5048, together with belt tensions, starting and stopping conditions, and pulley and shaft calculations. For the general structure of conveyors see our belt conveyor guide.
1. Data Required
| Data | Example | Why It Matters |
|---|---|---|
| Capacity (Q) | t/h | Determines belt width and speed |
| Material and loose bulk density (ρ) | Chippings ~1.4–1.6 t/m³ | Converts volumetric capacity to tonnes |
| Maximum lump size | mm | Minimum belt width and loading chute |
| Conveyor length (L) and lift (H) | m | Motor power and incline |
| Incline angle | degrees | Capacity reduction and material slip-back |
| Operating conditions | Dust, moisture, temperature, operating hours | Belt and idler selection |
2. Belt Speed Selection
The higher the belt speed, the more material a given belt width carries; but wear, dust, spillage and impact at the loading point also increase. In crushing and screening plants, belt speeds for crushed stone are mostly chosen in the range of about 1.5–3 m/s. Lower speeds are preferred for coarse, sharp material, at loading points and on stacking conveyors; higher speeds can be used for fine, uniform material and long-distance conveyors.
3. Capacity Calculation
The mass capacity of a belt conveyor is:
Q (t/h) = 3600 × A (m²) × v (m/s) × ρ (t/m³) × k
- A: Cross-sectional area of the material on the belt; depends on belt width, troughing angle and the material’s surcharge (dynamic repose) angle.
- k: Incline factor (1 when horizontal).
For three-roll idlers with a troughing angle of about 35°, the cross-sectional area for crushed stone can in practice be estimated as A ≈ 0.16 × (0.9B − 0.05)² (B: belt width, m). The table below shows approximate values calculated with this approach, allowing an 80% fill margin:
| Belt Width | Approx. Cross-Section (A) | Approx. Capacity (v = 2 m/s, ρ = 1.6 t/m³, 80% fill) |
|---|---|---|
| 500 mm | 0.026 m² | ~235 t/h |
| 650 mm | 0.046 m² | ~420 t/h |
| 800 mm | 0.072 m² | ~660 t/h |
| 1000 mm | 0.116 m² | ~1,065 t/h |
| 1200 mm | 0.170 m² | ~1,565 t/h |
| 1400 mm | 0.234 m² | ~2,155 t/h |
Capacity is lower with flatter troughing angles (e.g. 20°), with sticky or free-rolling materials and on inclined conveyors. The maximum lump size must also be checked separately when choosing belt width; for coarse, angular stone the belt must be wide enough relative to lump size.
Incline Factor and Maximum Incline
| Incline | Approx. Factor (k) |
|---|---|
| 0° | 1.00 |
| 6° | 0.98 |
| 10° | 0.95 |
| 14° | 0.91 |
| 18° | 0.85 |
| 20° | 0.81 |
The maximum incline that can be conveyed on a plain belt depends on the material: lower for rounded gravel, higher for crushed angular stone and damp sand; for crushed stone around 16–18° is generally considered the upper limit. Profiled (chevron) or corrugated sidewall belts are used for steeper inclines.
4. Motor Power Calculation
The peripheral force needed to move the conveyor consists of horizontal friction resistances and the force needed to lift the material. A simplified approach:
F ≈ C × f × L × g × (mR + 2mB + mG) + H × g × mG
P (kW) = F × v / (1000 × η)
| Symbol | Meaning | Typical Value |
|---|---|---|
| C | Length coefficient (for secondary resistances on short conveyors) | ~2.4 (50 m), ~1.9 (100 m), ~1.5 (200 m) |
| f | Artificial friction coefficient | ~0.02 (normal conditions); higher with poor alignment and dust |
| mR | Rotating mass of carrying and return idlers (kg/m) | Depends on idler type and spacing |
| mB | Belt mass (kg/m) | From the belt catalogue |
| mG | Material mass (kg/m) = Q / (3.6 × v) | — |
| η | Drive efficiency (motor + gearbox) | ~0.85–0.95 |
The power required just for lifting can be calculated quickly with Plift (kW) ≈ Q (t/h) × H (m) / 367.
Worked Example
Let capacity be 500 t/h, belt speed 2 m/s, length 100 m, lift 10 m and belt width 800 mm; assume a belt mass of about 12 kg/m and an idler rotating mass of about 15 kg/m:
| Step | Calculation | Result |
|---|---|---|
| Material mass | mG = 500 / (3.6 × 2) | ≈ 69.4 kg/m |
| Horizontal resistances | 1.9 × 0.02 × 100 × 9.81 × (15 + 2×12 + 69.4) | ≈ 4,040 N |
| Lift resistance | 10 × 9.81 × 69.4 | ≈ 6,810 N |
| Total peripheral force | 4,040 + 6,810 | ≈ 10,850 N |
| Drum power | 10,850 × 2 / 1000 | ≈ 21.7 kW |
| Motor power (η = 0.9) | 21.7 / 0.9 | ≈ 24 kW → 30 kW motor selected |
Check: lifting power alone is 500 × 10 / 367 ≈ 13.6 kW, consistent with the table. Motor selection allows a margin for starting conditions, loaded starts and possible overloads; the gearbox ratio is set by the drum speed (gearbox calculation).
5. Other Design Checks
- Belt type and strength: Carcass type and number of plies according to the required belt tension (conveyor belt guide).
- Idler spacing and type: Impact idlers or impact beds at the loading point (conveyor idler sizes).
- Pulley diameters: Minimum pulley diameter according to belt type (drive pulley guide).
- Take-up: Screw or gravity take-up (take-up assembly).
- Backstop on inclined conveyors: Prevents run-back when power is lost.
- Safety: Pull cord switches, misalignment and slip sensors (conveyor safety equipment).
Conveyor Types
| Type | Use |
|---|---|
| Troughed belt conveyor | The most common type in crushing and screening plants |
| Radial stacking conveyor | Forming arc-shaped stockpiles (stockyard) |
| Profiled and corrugated sidewall belt conveyor | Steep-incline conveying |
| Overland conveyor | Conveying from pit to plant (loading and haulage) |
| Screw and chain conveyors | Fine, dusty or special materials |
Common Mistakes
- Using the wrong material density (loose bulk density should be used, not particle density).
- Ignoring the incline factor and fill margin.
- Leaving no starting and overload margin on motor power.
- Not considering lump size when choosing belt width.
- Ignoring secondary resistances (length coefficient) on short conveyors.
Frequently Asked Questions
How is conveyor capacity calculated?
With Q = 3600 × A × v × ρ × k; the cross-sectional area is set by belt width and troughing angle.
How many tonnes does an 800 mm belt carry?
With about 35° troughing at 2 m/s and chippings, in practice several hundred tonnes per hour (in the order of 600–700 t/h); material and incline change this value.
How is conveyor motor power found?
Horizontal resistances and the lift force are added, multiplied by belt speed and divided by efficiency; a starting margin is then added.
What is the maximum incline for a conveyor?
On a plain belt it is generally about 15–20° depending on the material; profiled belts are used for steeper inclines.
Quick Preliminary Sizing Table
The table below gives an idea of belt width and speed selection for capacities common in crushing and screening plants (chippings, ~35° troughing, horizontal or slightly inclined conveyor). The final choice must be checked against lump size, incline and loading conditions.
| Capacity | Possible Belt Width | Possible Belt Speed |
|---|---|---|
| ~100–200 t/h | 500–650 mm | ~1.5–2 m/s |
| ~200–400 t/h | 650–800 mm | ~1.5–2.5 m/s |
| ~400–700 t/h | 800–1000 mm | ~2–2.5 m/s |
| ~700–1200 t/h | 1000–1200 mm | ~2–3 m/s |
Field Example: Capacity Loss on an Inclined Conveyor
Suppose a crusher discharge conveyor in a plant cannot carry its design capacity and overflows at the loading point. Investigation shows that after site alterations the conveyor was installed steeper than designed, and that material falls onto the belt at the loading point before reaching belt speed. When the incline factor and loading chute are reassessed and the belt speed is increased somewhat, with the motor power checked, the capacity problem is solved. This example shows that small geometry changes on site directly affect the conveyor calculation.
Glossary
- Troughing angle: The angle the wing rolls of a carrying idler set make with the horizontal.
- Surcharge angle: The surface slope the material forms on the moving belt.
- Peripheral force: The total force the drive pulley must transmit to the belt.
- Artificial friction coefficient (f): A coefficient representing idler and belt movement resistances.
- Backstop: A drive element that prevents reverse running on an inclined conveyor.
More Questions
How is conveyor belt speed calculated?
With v = π × D × n / 60, where D is the drum diameter (m) and n the drum speed (rpm).
How does conveyor length affect motor power?
As length increases, idler and belt movement resistances increase; on short conveyors the share of secondary resistances is proportionally higher.
Is a frequency inverter needed on a conveyor?
It is useful for soft starting and speed control on long, high-power conveyors; direct-on-line or star–delta starting is common on short plant conveyors.
CSP Mühendislik Support
CSP Mühendislik designs and fabricates belt and stacking conveyors for crushing and screening plants and supplies belts, idlers, pulleys, scrapers and drive parts. For your parts requirements see our belt conveyor spare parts page and conveyor spare parts guide, and for our equipment our products page.




