Conveyor spare parts are the belts, idlers, pulleys, scrapers, skirt rubber, take-up assemblies, drives and safety equipment that keep belt conveyors running continuously, safely and efficiently. In crushing and screening plants, conveyors are the “arteries” that link the equipment together. A single conveyor stopping can halt the whole line from the crusher to the stockpile. Correct selection and stock planning of conveyor parts is therefore one of the foundations of plant efficiency.
In this guide we introduce conveyor components one by one and cover selection criteria, failure symptoms and stock recommendations. For the general structure and maintenance of conveyors see our belt conveyor guide, and for our range see our belt conveyor spare parts page.
Conveyor Components and Spare Parts List
| Component | Function | Guide |
|---|---|---|
| Conveyor belt | Carries the material | Conveyor belt |
| Carrying idlers (troughed idler sets) | Support the loaded belt | Conveyor idlers |
| Return idlers | Support the empty return belt | Conveyor idlers |
| Impact idlers and impact beds (impact bars) | Absorb impact at the loading point | Impact idlers |
| Drive pulley and lagging | Transfers power to the belt | Drive pulley |
| Tail and snub pulleys | Turn and guide the belt | Tail pulley |
| Take-up assembly | Provides belt tension | Take-up assembly |
| Belt scrapers | Clean off carryback | Belt scrapers |
| Skirt rubber and loading chute | Prevent spillage and dust | Skirt rubber |
| Safety equipment | Pull cord switch, misalignment and slip sensors | Conveyor safety |
| Gearbox, motor, coupling, backstop | Drive and safety | Gearbox maintenance |
| Bearings and plummer blocks | Support the pulleys | Bearing guide |
| Belt splicing materials | Vulcanised or mechanical splice | Conveyor belt |
Conveyor Belt
The conveyor belt is the most expensive and most critical component of a conveyor. The carcass (number of textile plies or steel cord), top and bottom cover thickness and cover grade (resistance to abrasion, cutting, heat and oil) are chosen to suit the application. Cut- and impact-resistant covers come first on belts carrying crushed rock, while abrasion resistance matters most on long belts carrying sand. The main causes of shortened belt life are impact at the loading point, mistracking, seized idlers, tramp metal and poor splicing.
Conveyor Idlers
Idlers are the most numerous parts of a conveyor. A seized idler cuts the underside of the belt and increases friction; broken idler edges can tear the belt.
- Dimensions: Idler diameter, idler length (according to belt width and troughing angle), shaft diameter and shaft end type (spanner flats, drilled) must be specified correctly.
- Sealing: In dusty and wet environments, labyrinth-sealed, lubricated-for-life idlers are preferred.
- Types: Carrying (troughed), return (flat or V-type), impact (rubber-ringed), self-aligning (training) and disc return idlers.
- Impact beds: At the loading point, slider-type impact beds (impact bars) can be used instead of impact idlers; they keep the belt flat and sealed, improving skirt performance.
Pulleys and Lagging
The drive pulley transfers power to the belt by friction. Lagging (rubber or ceramic-embedded rubber) increases friction and prevents slip. When the lagging wears, the belt slips, heats up and drive efficiency falls. Tail and snub pulleys guide the belt; material build-up and bearing failures are their common problems.
Scrapers and Skirt Rubber
Belt scrapers (primary and secondary scrapers, V-plough scrapers) clean off material stuck to the belt, reducing spillage on the return side, idler and pulley problems and clean-up labour. Skirt rubber prevents material and dust escaping at the loading point. Although low in cost, these two part groups have a significant effect on the conveyor’s total maintenance cost.
Take-Ups and Safety Equipment
Belt tension is provided by screw, gravity or hydraulic take-up systems. Insufficient tension causes slip; excessive tension overloads the belt and bearings. Safety equipment (pull cord switches, emergency stop buttons, misalignment and slip sensors, backstops) is essential for both personnel safety and equipment protection. For safety topics see our occupational safety guide.
Information Needed When Selecting Conveyor Spare Parts
| Part | Information Required |
|---|---|
| Belt | Width, length, carcass type and strength, number of plies, cover thicknesses and grade, splice type |
| Idler | Diameter, length, shaft diameter, shaft end type and dimensions, bearing type |
| Pulley | Diameter, face width, shaft diameter and length, bearing centres, lagging type and thickness |
| Scraper | Belt width, pulley diameter, belt speed, mounting space |
| Skirt rubber | Thickness, height, material (rubber, polyurethane) |
| Gearbox | Make, model, ratio, power, shaft dimensions |
Stock Recommendations
- A set number of spare idlers (carrying, return, impact) for each belt width and idler type,
- A spare belt roll and splicing materials (vulcanising kit, mechanical fastener set) for critical conveyors,
- Scraper blades and a roll of skirt rubber,
- A critical drive pulley, or at least pulley bearings and housings,
- A spare gearbox or overhaul kit for critical conveyors,
- Pull cord switches and sensors.
Standardising belt widths, idler diameters and shaft sizes across the plant reduces stock variety and makes finding parts easier in emergencies.
Common Problems and Related Parts
| Problem | Related Part | Solution |
|---|---|---|
| Belt mistracking | Idlers, pulleys, loading arrangement | Alignment, self-aligning idlers |
| Spillage on the return side | Scrapers | Adjust or replace scrapers |
| Spillage and dust at the loading point | Skirt rubber, impact bed | Renew skirt rubber and impact bed |
| Belt slip | Pulley lagging, take-up | Renew lagging, adjust tension |
| Cuts and tears in the belt | Seized idlers, tramp metal | Replace idlers, metal separation |
| Gearbox overheating | Gearbox, coupling | Oil and alignment check |
On conveyors fitted with belt scales, the condition of the parts also affects weighing accuracy; for details see our belt scale guide, and to prevent belt tears caused by metal see our magnetic separator guide.
Frequently Asked Questions
What are the parts of a conveyor?
The main ones are the belt, carrying and return idlers, impact idlers or impact beds, drive, tail and snub pulleys, take-up assembly, scrapers, skirt rubber, gearbox and motor, and safety equipment.
How are conveyor idler dimensions determined?
Belt width and troughing angle determine idler length; load and belt speed determine idler diameter and bearing type. A compatible idler is selected by measuring the diameter, length, shaft diameter and shaft end dimensions of the existing idler.
When should a conveyor belt be replaced?
When the top cover is close to the carcass, when the carcass is damaged, or when repair costs exceed the economic limit.
Can pulley lagging be renewed?
Yes. Worn lagging can be renewed on site by cold bonding or in the workshop by hot vulcanising.
Factors Affecting Conveyor Part Prices
| Part | Main Factors Affecting Price |
|---|---|
| Conveyor belt | Width, carcass type and strength, number of plies, cover thickness and grade (abrasion, heat, oil resistance) |
| Conveyor idler | Diameter, length, tube wall thickness, shaft diameter, bearing type, sealing system, rubber covering |
| Pulley | Diameter, face width, shaft material and diameter, lagging type (rubber, ceramic), locking elements |
| Scraper | Belt width, blade material (polyurethane, tungsten-carbide-tipped), tensioning system |
| Skirt rubber | Material, thickness, length |
When comparing idler and belt prices, consider expected life and downtime cost rather than unit price. A cheap idler with poor sealing can seize quickly and cut the belt.
Conveyor Belt Types
- Textile carcass (EP) belts: The most common type in crushing and screening plants.
- Steel cord belts: Conveyors requiring long distances and high tension.
- Heat-resistant belts: Hot material (clinker, slag).
- Oil-resistant belts: Carrying oily material.
- Profiled (chevron, cleated) belts: Prevent material sliding back on inclined conveyors.
- Corrugated sidewall belts: Steep-incline conveying.
Glossary
- Troughing angle: The angle the wing rolls of a carrying idler set make with the horizontal.
- Carryback: Material that remains stuck to the belt after discharge.
- Impact bed (impact bar): A slider-type belt support system at the loading point.
- Lagging: The rubber or ceramic covering on a pulley surface.
- Vulcanised splice: Joining belt ends with heat and pressure.
More Questions
Why does a conveyor idler stop turning?
Bearing failure, dust and water ingress, material jamming or a bent shaft are the main causes. A seized idler should be replaced immediately.
What determines the price per metre of conveyor belt?
Belt width, carcass strength, number of plies and cover thicknesses are the main factors that determine price.
What are the elements of a belt conveyor?
The belt, idlers, pulleys, take-up assembly, scrapers, skirt rubber, drive unit, frame and safety equipment.
CSP Mühendislik Support
CSP Mühendislik supplies conveyor belts, idlers, pulleys, scrapers, skirt rubber, take-up systems and safety equipment, and provides conveyor design, fabrication and service, maintenance and repair. You can send your parts requirements via our belt conveyor spare parts page or our WhatsApp line. For other equipment, see our spare parts page.




