On a belt conveyor, the point where material is loaded onto the belt is where most spillage, dust and belt damage occur. The parts that keep the material on the belt in this zone and stop it overflowing the edges are called skirt rubber (skirting), and the structure that carries the skirt rubber and guides the material is called the loading chute (skirtboard). A well-designed and well-adjusted loading zone significantly reduces spillage, dust, belt wear and cleaning labour.
In this guide we cover the function of skirt rubber and the loading chute, material options, correct adjustment, the relationship with impact beds, maintenance and replacement steps and spare part selection. For general belt conveyor maintenance, see our belt conveyor guide.
Function of Skirt Rubber and the Loading Chute
- Prevents spillage: Stops material overflowing the belt edges.
- Limits dust: Reduces the spread of dust raised during loading.
- Centres the material: Helps the load settle in the middle of the belt, reducing mistracking.
- Protects the belt: When adjusted correctly, it seals without damaging the belt.
Material Options
| Material | Characteristics | Use |
|---|---|---|
| Natural rubber / SBR | Economical, flexible | General applications |
| Polyurethane | High wear resistance | Abrasive material |
| Dual seal systems | Primary + secondary sealing | Dusty and fine material |
Skirt rubber must be softer than the belt cover; otherwise it wears the belt.
Correct Adjustment
- Skirt rubber should touch the belt lightly; pressing too hard wears the belt and increases motor load.
- The gap between the belt and the chute plate should be set so that the plate cannot cut the belt and coarse particles cannot become trapped in the gap.
- An impact bed or closely spaced impact idlers should be used in the loading zone to stop belt sag; a sagging belt opens a gap under the skirt rubber and spillage increases.
- The chute should be long enough for the material to reach belt speed and settle.
Wear and Failure Signs
- Spillage and dust in the loading zone,
- Skirt rubber worn, torn or no longer in contact with the belt,
- Grooves in the belt top cover in line with the skirts,
- Rocks trapped between the chute plate and the belt,
- Wear and holes in the chute liners.
Inspection and Maintenance
| Check | Interval | Method |
|---|---|---|
| Spillage and dust | Daily | Walk-around |
| Skirt rubber contact | Weekly | Check and adjust with the conveyor locked out |
| Chute liners | Monthly | Wear and holes |
| Impact bed/idlers | Monthly | Wear and damage |
Replacing Skirt Rubber
- The conveyor is stopped and locked out.
- Clamps or fixings are loosened and the old rubber removed.
- The new rubber is positioned to touch the belt lightly.
- The clamps are tightened; contact and spillage are checked during operation.
- As it wears, the rubber is slid down and readjusted (on systems with adjustable clamps).
Common Mistakes
- Pressing the skirt rubber too hard onto the belt,
- Using rubber harder than the belt cover,
- Not using an impact bed in the loading zone,
- A chute design that is too short,
- Not checking the gap between the chute plate and the belt.
Troubleshooting Table
| Symptom | Possible cause | Solution |
|---|---|---|
| Spillage | Worn rubber, belt sagging | Adjust/replace the rubber, add an impact bed |
| Grooves in the belt | Rubber too hard or pressed too hard | Softer rubber, correct contact |
| Dust | Short chute, single-layer sealing | Lengthen the chute, dual seal, dust curtains |
| Rocks trapped | Wrong plate-to-belt gap | Adjust the gap |
An Example from the Field
At one plant’s transfer point there was constant spillage and dust; cleaning took half of one operator’s time every shift. An impact bed was added to the loading zone, the chute was lengthened and an adjustable dual-seal skirt system was installed. Spillage fell dramatically and the cleaning labour was freed up. For other dust control measures, see our article on dust and noise control.
Pre-Purchase Checklist
- Have the belt width and chute length been determined?
- Have skirt rubber thickness, height and material been chosen?
- Is a clamp system needed?
- Is an impact bed or impact idlers needed?
Frequently Asked Questions
How often is skirt rubber replaced?
It depends on the material and adjustment; with adjustable systems, the rubber can be slid down as it wears and used for a long time.
Does skirt rubber wear the belt?
With hard material or excessive pressure, yes; with the right material and light contact, it does not.
Effect of Transfer Point Design on Skirt Rubber
The performance of skirt rubber depends largely on the design of the transfer point. If material falls onto the belt at the wrong angle, from a great height or at a speed very different from the belt speed, skirt rubber alone cannot prevent spillage and dust. A good transfer point:
- Releases material in the direction of belt travel at close to belt speed (curved chute design),
- Places material in the centre of the belt,
- Minimises drop height,
- Prevents belt sag in the loading zone with an impact bed,
- Provides a chute long enough for the material to settle.
Skirting Systems: Single and Dual Layer
| System | Construction | Suitable for |
|---|---|---|
| Single-layer skirt | A single rubber strip held by clamps | Coarse, low-dust material |
| Dual-layer (primary + secondary) skirt | A wear liner inside, a flexible sealing strip outside | Fine and dusty material |
| Self-adjusting skirt | Constant light contact with the belt by spring or weight | A maintenance-friendly solution that rarely needs adjustment |
Chute Wear Liners
The inner surfaces of the loading chute wear from sliding and impacting material. Wear plates (400–500 HB), ceramic liners or rubber liners can be used inside the chute. The gap between the wear liners and the belt should be set so that material does not become trapped but the skirt rubber is not overloaded. As the liner wears, this gap can change, so the liners and skirts should be checked together.
Effect of Operating Conditions
| Condition | Effect | Recommendation |
|---|---|---|
| High drop height | Belt sag, spillage, skirt wear | Improve the chute design, impact bed |
| Fine, dry material | Dust escape | Dual-layer skirt, dust curtains, extraction if needed |
| Abrasive material | Skirt and liner wear | Polyurethane skirt, durable liners |
| Belt mistracking | Spillage on one side | Eliminate the root cause of mistracking |
Maintenance Record Form
| Field | Record |
|---|---|
| Transfer point | Conveyor and location |
| Spillage/dust observation | None / slight / marked |
| Skirt adjustment | Date and adjustment made |
| Liner condition | Wear and gap |
| Impact bed | Condition and replacement |
Stock Planning
- Keep enough skirt rubber on the roll for each belt width.
- Keep spare clamp parts and fixings.
- Keep spare impact bed bars or impact idlers for critical transfer points.
More Questions
How is skirt rubber height chosen?
According to the distance between the chute plate and the belt and the clamp system; some extra height is left as a wear allowance.
What does a dust curtain do?
Flexible curtains hung at the chute exit help raised dust settle before it leaves the chute.
Impact bed or impact idlers?
An impact bed provides continuous support, completely preventing belt sag and improving sealing; impact idlers are a more economical solution. With heavy impact and fine material, an impact bed is more effective.
Spare Parts and Service for Skirt Rubber
CSP Mühendislik supplies skirt rubber, clamp systems, impact beds and loading chute liners as part of its belt conveyor spare parts range, and provides service support for belt conveyor transfer point improvements. Share your belt width on WhatsApp and we will prepare a quote quickly.




