In a vertical shaft impactor (VSI), material passes through the feed tube at the top of the crusher and falls into the centre of the rotor. The part on the rotor’s upper cover that protects the opening where material enters is called the feed eye ring. Although these two parts are small and relatively cheap, they directly determine whether the rotor is fed correctly, whether wear inside the rotor is even and whether rotor balance is maintained. When the feed tube is off-centre, one side of the rotor receives more material; the rotor wears unevenly, vibration starts and the rotor tips wear out early.
In this guide we bring together the function of these parts, the importance of alignment, wear signs, replacement steps and spare part selection. For the general working principle of the VSI, see our vertical shaft impactor guide.
Function of the Feed Tube and Feed Eye Ring
- Directs material to the exact centre of the rotor: Essential for all rotor ports to receive equal material.
- Protects the rotor upper cover: The feed eye ring prevents falling material from wearing the rotor cover.
- Calms the feed flow: A tube of the correct diameter and length lets material enter the rotor evenly.
- Separates cascade feed: In crushers with a cascade feature, it works together with the arrangement that sets the ratio of feed through and around the rotor.
Why Is Alignment So Important?
Even a small offset between the axis of the feed tube and the rotor axis causes more material to fall on one side of the rotor. The consequences:
- The wear plates inside the rotor and the rotor tips wear faster on one side,
- Rotor balance is upset and the vibration switch trips frequently,
- The feed eye ring and the distributor plate wear on one side,
- The load on the bearing cartridge increases.
The feed tube should therefore be centred at every service and every time the lid is opened and closed.
Material Options
| Material | Characteristics | Use |
|---|---|---|
| Wear steel | Economical, easy to replace | Low to moderately abrasive material |
| Chrome cast iron | High wear resistance | Abrasive rock |
| Tungsten carbide reinforced | Highest wear resistance | Very abrasive material, long service intervals |
| Polyurethane/rubber-lined tube | Impact damping, low noise | Upper sections of the feed tube |
Wear and Failure Signs
- Thinning or gouging of the feed eye ring,
- The lower end of the feed tube wearing and getting shorter,
- An increasing gap between the tube and the ring,
- Wear marks on the rotor cover,
- One-sided wear inside the rotor,
- Increased vibration.
Inspection and Maintenance Schedule
| Check | Interval | Method |
|---|---|---|
| Feed tube alignment | Every shift / every time the lid is opened | Centring tool or measurement |
| Feed eye ring wear | Every 4–8 hours (abrasive material) | Visual check and measurement |
| Length of the tube’s lower end | Weekly | Measurement |
| Rotor cover | Weekly | Check for wear marks |
Replacement Step by Step
- The crusher and feeder are stopped, the rotor is confirmed to have stopped completely and LOTO is applied.
- The crusher lid is opened (with lifting equipment if necessary).
- The feed tube is removed and the feed eye ring fasteners are released.
- The rotor cover and the ring seating surface are cleaned and checked.
- The new ring is fitted and secured.
- The new or existing feed tube is fitted and centred on the rotor axis.
- The gap between the tube and the ring is set to the manufacturer’s value.
- The lid is closed; vibration is checked during an idle run.
Common Mistakes
- Not checking tube alignment after closing the lid,
- Running the ring until it wears through, causing rotor cover wear,
- Running with a shortened tube, so material enters the rotor irregularly,
- Using a tube of the wrong diameter, causing capacity and distribution problems,
- Not checking the cascade setting after replacing the feed tube.
Troubleshooting Table
| Symptom | Possible cause | Solution |
|---|---|---|
| Rotor wearing on one side | Feed tube off-centre | Centre the tube |
| Vibration increasing | Uneven feeding, build-up inside the rotor | Alignment and rotor cleaning |
| Rotor cover wearing | Worn feed eye ring | Replace the ring |
| Capacity has dropped | Tube blockage or wrong diameter | Check the tube and feed |
An Example from the Field
At a basalt manufactured sand plant, the VSI rotor tips on one side were wearing out much faster than the others and the vibration alarm was tripping frequently. The investigation found that after a lid service the feed tube had been left a few centimetres off-centre. The tube was centred and an alignment check was added to the lid closing procedure; wear evened out and the vibration alarms stopped.
Cost and Life Analysis
The feed eye ring and feed tube are among the cheapest wear parts of a VSI. On the other hand, a worn ring puts the rotor cover at risk, and an off-centre tube puts the rotor tips and the bearing cartridge at risk. Replacing these parts regularly reduces rotor and bearing costs and lowers the total cost per tonne.
Pre-Purchase Checklist
- Have the VSI make/model and rotor type been identified?
- Have the feed tube diameter and length been measured?
- Are the feed eye ring dimensions and fixing type known?
- Has the material been chosen according to abrasiveness?
Safety
- A VSI rotor keeps turning for a long time after the motor stops; wait until it has stopped completely before opening the lid.
- The lid and feed tube are heavy; use lifting equipment.
Frequently Asked Questions
How often is the feed eye ring replaced?
It depends on the abrasiveness of the material and the tonnage; abrasive materials require frequent checks.
Why does the feed tube diameter matter?
The diameter affects the amount and distribution of material entering the rotor; it must be compatible with the rotor type.
How is alignment checked?
With the manufacturer’s centring tool or by measuring the gap between the tube and the ring around the circumference.
Are the feed eye ring and the distributor plate the same?
No. The ring protects the inlet in the rotor’s upper cover; the distributor plate at the bottom of the rotor distributes material to the ports.
Assessing It Together with the Feed System
The VSI feed tube should be assessed together with the whole feed system, not on its own. VSIs like continuous, controlled feeding; if the feed fluctuates, the rotor load and wear pattern fluctuate too.
- Feed bin and feeder: A level-controlled surge bin and a variable frequency feeder keep the VSI at constant power.
- Feed conveyor: Should drop material in the centre of the feed box.
- Feed box: Should let material flow smoothly into the tube and stop it changing direction by hitting the side walls.
- Cascade arrangement: In VSIs with cascade, the ratio of feed through and around the rotor can be adjusted; this ratio sets the balance between product and wear.
Relationship Between Feed Size and Tube Diameter
The feed tube diameter and the feed eye opening are related to the largest particle size the rotor can accept. Particles larger than the rotor type allows can bridge in the tube or at the rotor inlet and become trapped in the rotor, causing imbalance and damage. The screen aperture before the VSI should therefore be chosen according to the maximum feed size suitable for the rotor type.
Effect of Operating Conditions
| Condition | Effect | Recommendation |
|---|---|---|
| Fluctuating feed | Uneven rotor load and wear | Level-controlled feeding |
| Oversized feed | Tube and ring damage, bridging | Check the pre-screen aperture |
| Wet material | Sticking inside the tube | Moisture control, regular cleaning |
| Abrasive material | Rapid wear of the ring and tube end | Carbide-reinforced parts |
Maintenance Record Form
| Field | Record |
|---|---|
| Alignment check | Date and measured offset |
| Feed eye ring | Thickness and replacement date |
| Tube lower end | Measured length |
| Rotor wear pattern | Even / one-sided |
OEM or Aftermarket?
For the feed tube and feed eye ring, dimensional fit (inside and outside diameter, length, fixing points) and material quality are decisive. With aftermarket parts, check that the ring seats fully on the rotor cover and that the tube fits its seat in the lid without play and allows centring.
Stock Planning
- Together with the rotor tips, the feed eye ring is one of the most frequently replaced parts; keep at least one spare in stock.
- Keep a spare tube or a replaceable tip section for the wearing lower part of the feed tube.
More Questions
How long should the feed tube be?
The distance between the lower end of the tube and the rotor is specified by the manufacturer; a tube shortened by wear changes this distance and affects feeding.
How does the feed eye ring protect the rotor cover?
It stops falling material hitting the inner edge of the rotor cover, preventing cover wear; once the ring is worn, the cover starts to wear directly.
Who should carry out the alignment?
The team servicing the lid should check alignment after the lid is closed and record it on the maintenance form.
Spare Parts and Service for the Feed Tube and Ring
CSP Mühendislik supplies feed tubes, feed eye rings and other rotor wear parts for vertical shaft impactors as part of its VSI crusher spare parts range, and provides service support for rotor maintenance and alignment. Share your VSI model on WhatsApp for a quick quote.




